ENUM WIPHY_FLAGS(9)                    Device registration                    ENUM WIPHY_FLAGS(9)



NAME
       enum_wiphy_flags - wiphy capability flags

SYNOPSIS
       enum wiphy_flags {
         WIPHY_FLAG_NETNS_OK,
         WIPHY_FLAG_PS_ON_BY_DEFAULT,
         WIPHY_FLAG_4ADDR_AP,
         WIPHY_FLAG_4ADDR_STATION,
         WIPHY_FLAG_CONTROL_PORT_PROTOCOL,
         WIPHY_FLAG_IBSS_RSN,
         WIPHY_FLAG_MESH_AUTH,
         WIPHY_FLAG_SUPPORTS_SCHED_SCAN,
         WIPHY_FLAG_SUPPORTS_FW_ROAM,
         WIPHY_FLAG_AP_UAPSD,
         WIPHY_FLAG_SUPPORTS_TDLS,
         WIPHY_FLAG_TDLS_EXTERNAL_SETUP,
         WIPHY_FLAG_HAVE_AP_SME,
         WIPHY_FLAG_REPORTS_OBSS,
         WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD,
         WIPHY_FLAG_OFFCHAN_TX,
         WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL,
         WIPHY_FLAG_SUPPORTS_5_10_MHZ,
         WIPHY_FLAG_HAS_CHANNEL_SWITCH
       };

CONSTANTS
       WIPHY_FLAG_NETNS_OK
           if not set, do not allow changing the netns of this wiphy at all

       WIPHY_FLAG_PS_ON_BY_DEFAULT
           if set to true, powersave will be enabled by default -- this flag will be set
           depending on the kernel's default on wiphy_new, but can be changed by the driver if it
           has a good reason to override the default

       WIPHY_FLAG_4ADDR_AP
           supports 4addr mode even on AP (with a single station on a VLAN interface)

       WIPHY_FLAG_4ADDR_STATION
           supports 4addr mode even as a station

       WIPHY_FLAG_CONTROL_PORT_PROTOCOL
           This device supports setting the control port protocol ethertype. The device also
           honours the control_port_no_encrypt flag.

       WIPHY_FLAG_IBSS_RSN
           The device supports IBSS RSN.

       WIPHY_FLAG_MESH_AUTH
           The device supports mesh authentication by routing auth frames to userspace. See
           NL80211_MESH_SETUP_USERSPACE_AUTH.

       WIPHY_FLAG_SUPPORTS_SCHED_SCAN
           The device supports scheduled scans.

       WIPHY_FLAG_SUPPORTS_FW_ROAM
           The device supports roaming feature in the firmware.

       WIPHY_FLAG_AP_UAPSD
           The device supports uapsd on AP.

       WIPHY_FLAG_SUPPORTS_TDLS
           The device supports TDLS (802.11z) operation.

       WIPHY_FLAG_TDLS_EXTERNAL_SETUP
           The device does not handle TDLS (802.11z) link setup/discovery operations internally.
           Setup, discovery and teardown packets should be sent through the NL80211_CMD_TDLS_MGMT
           command. When this flag is not set, NL80211_CMD_TDLS_OPER should be used for asking
           the driver/firmware to perform a TDLS operation.

       WIPHY_FLAG_HAVE_AP_SME
           device integrates AP SME

       WIPHY_FLAG_REPORTS_OBSS
           the device will report beacons from other BSSes when there are virtual interfaces in
           AP mode by calling cfg80211_report_obss_beacon.

       WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD
           When operating as an AP, the device responds to probe-requests in hardware.

       WIPHY_FLAG_OFFCHAN_TX
           Device supports direct off-channel TX.

       WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL
           Device supports remain-on-channel call.

       WIPHY_FLAG_SUPPORTS_5_10_MHZ
           Device supports 5 MHz and 10 MHz channels.

       WIPHY_FLAG_HAS_CHANNEL_SWITCH
           Device supports channel switch in beaconing mode (AP, IBSS, Mesh, ...).

AUTHOR
       Johannes Berg <johannes AT sipsolutions.net>
           Author.

COPYRIGHT
Kernel Hackers Manual 4.8.                 January 2017                       ENUM WIPHY_FLAGS(9)